ENGINEERING INSIGHTS

PCB • PCBA • Control Boards • Electronics Manufacturing
Practical knowledge from design and component sourcing to PCB assembly, testing and mass production.
click

How to Choose an Analog FPV Camera: W12 Specs Explained

By RONGHE Engineering Team October 17th, 2026 26 views

To choose an analog FPV camera, first confirm that its video output matches the intended video path. Then check field of view, supply requirements, physical dimensions, and weight. Use the resolution label as one part of the evaluation, alongside a sample image from the complete system.

This guide uses the RONGHE W12 analog FPV camera module as a practical example. The W12 is specified at 1200TVL with CVBS output and PAL/NTSC selection through its on-screen display (OSD). The specifications below help show what to compare before requesting a sample or discussing a project.

A Quick Analog FPV Camera Selection Checklist

  • Video path: Confirm the required analog output and supported video standard.
  • Viewing area: Compare horizontal FOV with horizontal FOV, using the stated aspect ratio.
  • Power: Check the specified input range and current at the stated supply voltage.
  • Mechanical fit: Review the full dimensions, mounting details, and connector clearance.
  • Sample approval: Evaluate the image and agreed functions in the intended system.

1. Read TVL as an Analog Resolution Specification

TVL, or TV lines, describes visual resolution in analog video. It is different from a digital image format stated as a pixel width and height. Analog Devices explains the distinction between visual resolution and signal format, including the effect of bandwidth on visible detail.

The W12 specification lists 1200TVL. Keep that label intact when comparing the module; do not rewrite it as 1200p, 1080p, or a megapixel output. A TVL figure also does not establish the latency of the full video path. Check the actual image and response of the system you intend to use.

2. Compare Field of View on the Same Basis

A field-of-view value needs a direction. Horizontal FOV describes the view across the image; diagonal FOV describes the view from corner to corner. The image aspect ratio matters when relating these measurements. Edmund Optics distinguishes horizontal, vertical, and diagonal FOV in its imaging guidance.

For the W12, the specification lists a horizontal FOV of 99° and a diagonal FOV of 118° at 16:9. These are two descriptions of the viewing area, not competing specifications. When comparing another camera, make sure its quoted angle uses the same direction and aspect ratio.

For sample approval, define what must remain visible in the installed position. Evaluate the resulting framing with the intended display setup instead of selecting a camera from an unlabeled angle alone.

3. Check Input Voltage and Current Together

The W12 input specification is DC 5–20V. Its listed current is 140mA at 5V and 55mA at 12V. Keep each current figure paired with its supply voltage; neither figure is a constant current for the entire input range.

When discussing integration, identify the supply you intend to use and the electrical requirements of the assembled system. Confirm the current connector and pin assignment separately before connecting the module. This selection guide does not provide a wiring diagram.

4. Confirm CVBS Output and PAL/NTSC Support

CVBS is a composite analog video format. The W12 lists CVBS output with PAL/NTSC selection through OSD. These describe the signal to be handled by the rest of the video path. Analog Devices’ overview of analog video provides background on composite video and video formats.

Check the input requirements of the intended video transmitter and the receiving or display equipment. Confirm the selected video standard during sample testing. A camera specification alone does not prove compatibility with every flight controller, transmitter, or display.

If your project also needs other electronic modules, browse RONGHE UAV and FPV electronics, then review the requirements of each component and its interfaces separately.

5. Check the Complete Size and Weight

The W12 is listed at 19 x 19 x 26.5mm and 9.8g. Use the complete dimensions when reviewing the available space; the 19 x 19mm outline alone does not describe the module’s depth.

Confirm mounting details and the space needed for connectors and cables using the current mechanical information. Do not infer mounting-hole spacing from the outer dimensions or estimate a connector pinout from a product photograph.

RONGHE W12 Specifications at a Glance

  • Model: DL-W12; website designation RH-DL-W12
  • Image sensor: 1/3-inch CMOS
  • Resolution label: 1200TVL
  • Field of view: H 99° / D 118°, at 16:9
  • Video: CVBS; PAL/NTSC adjustable through OSD
  • Input voltage: DC 5–20V
  • Listed current: 140mA at 5V; 55mA at 12V
  • Dimensions: 19 x 19 x 26.5mm
  • Weight: 9.8g

Define What a Sample Must Demonstrate

Turn your selection criteria into a short sample-review checklist. Specify the video standard, supply condition, viewing area, mechanical fit, and image conditions you want to assess. If startup, OSD operation, or another function matters to the project, include it in the agreed test procedure.

Record the test procedure, functions evaluated, pass/fail criteria, and results for sample approval. Review the test requirements when the project changes.

For an assembly or manufacturing project, distinguish appearance inspection from function verification. Our guide to AOI and functional testing explains why the required checks and acceptance criteria should be defined for the project.

What to Include in a W12 Camera Inquiry

  • Required quantity and project stage
  • Intended supply and video standard
  • Viewing-area and mechanical requirements
  • Functions and image conditions to assess during sample approval
  • Any requested changes, with drawings or interface requirements where available

For a custom PCBA or assembly inquiry, also describe the requested manufacturing scope. If design files are available, use our PCBA quotation file checklist to organize the Gerber, BOM, placement, and test information relevant to the project.

Frequently Asked Questions

Does 1200TVL Mean 1200p?

No. TVL is a visual-resolution specification used for analog video, not a digital pixel-format label. The W12 specification should remain 1200TVL.

Is the W12 Field of View 99° or 118°?

Both values are listed, with different directions: 99° horizontal and 118° diagonal at 16:9. Keep the direction and aspect ratio attached to the number.

Why Are Two Current Values Listed?

They refer to different supply conditions: 140mA at 5V and 55mA at 12V. Use the specified test voltage with each value rather than applying either current across the whole input range.

Discuss Your Analog FPV Camera Requirements

Share the required quantity, supply condition, video standard, and mechanical requirements through the RONGHE contact page. Include any sample-approval or customization requirements so the requested scope can be reviewed.

AOI vs. FCT: What Each PCBA Test Can Verify,www.rohepcba.com
Previous
AOI vs. FCT: What Each PCBA Test Can Verify
Read More
RONGHE DL-W12 camera beside a PCBA test requirements checklist for test items, conditions, pass/fail criteria, and results.
Next
How to Define PCBA Test Requirements: A Buyer’s Checklist
Read More